Currency:

W5100_Shield

W5100_Shield
Quantity Available
In-stock: 5
Manufacturer Part W5100_Shield
Manufacturer China
Description W5100 Ethernet Shield for Arduino
Quantity Unit Price Extended Price
1 185,000đ 185,000đ
10 180,000đ 1,800,000đ
50 175,000đ 8,750,000đ
100 170,000đ 17,000,000đ
     
Enter Quantity
Email *
Vui lòng nhập chính xác Email
Họ tên
Bạn không thể viết lời bình liên tục!
Message *
Bạn chưa nhập nội dung bình luận!
Nội dung bình luận quá ngắn!
Nội dung bình luận quá dài!
Features
  • Microcontroller   AT91SAM3X8E
  • Operating Voltage   3.3V
  • Input Voltage (recommended)   7-12V
  • Input Voltage (limits)   6-20V
  • Digital I/O Pins   54 (of which 12 provide PWM output)
  • Analog Input Pins   12
  • Analog Outputs Pins   2 (DAC)
  • Total DC Output Current on all I/O lines   130 mA
  • DC Current for 3.3V Pin   800 mA
  • DC Current for 5V Pin   800 mA
  • Flash Memory   512 KB all available for the user applications
  • SRAM   96 KB (two banks: 64KB and 32KB)
  • Clock Speed   84 MHz

The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO board.

The Ethernet Shield has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled.

There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). The onboard microSD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the shield contained a full-size SD card slot; this is not supported.

The shield also includes a reset controller, to ensure that the W5100 Ethernet module is properly reset on power-up. Previous revisions of the shield were not compatible with the Mega and need to be manually reset after power-up.

The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable:

  • IEEE802.3af compliant
  • Low output ripple and noise (100mVpp)
  • Input voltage range 36V to 57V
  • Overload and short-circuit protection
  • 9V Output
  • High efficiency DC/DC converter: typ 75% @ 50% load
  • 1500V isolation (input to output)

NB: the Power over Ethernet module is proprietary hardware not made by Arduino, it is a third party accessory. For more information, see the datasheet

The shield does not come with the PoE module built in, it is a separate component that must be added on.

Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 11, 12, and 13 on the Duemilanove and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.

The shield provides a standard RJ45 ethernet jack.

The reset button on the shield resets both the W5100 and the Arduino board.

The shield contains a number of informational LEDs:

  • PWR: indicates that the board and shield are powered
  • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  • FULLD: indicates that the network connection is full duplex
  • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • RX: flashes when the shield receives data
  • TX: flashes when the shield sends data
  • COLL: flashes when network collisions are detected

The solder jumper marked "INT" can be connected to allow the Arduino board to receive interrupt-driven notification of events from the W5100, but this is not supported by the Ethernet library. The jumper connects the INT pin of the W5100 to digital pin 2 of the Arduino.

 

AT-SKY chuyên cung cấp sỉ và lẻ các loại linh kiện điện tửlinh kiện công suấtKit phát triểnBreakout BoardModule GSM/GPRS/GPSNhập khẩu cáclinh kiện điện tử chính hãng của các nhà sản xuất từ các quốc gia như China, Taiwan, Singapore, Thailand...Thiết kế, lập trình, gia công các mạch điện tử và chuyển giao công nghệ cho các quý công ty theo yêu cầu. AT-SKY luôn cam kết làm việc: “Uy tín – Đảm Bảo – Chất Lượng”.

 

 Mọi chi tiết xin liên hệcontact@at-sky.com.vn

 

 

arduino-mega2560-r3
Arduino Mega2560 R3
Arduino Mega2560 Rev3 (ATmega2560 MCU)
View more
Mã Sản phẩm: ARDUINO.MEGA2560.R3
Nhà sản xuất: China
SL Giá
1 310,000đ
10 305,000đ
50 300,000đ
100 295,000đ
Qty
310,000đ
w5100_shield
W5100_Shield
W5100 Ethernet Shield for Arduino
View more
Mã Sản phẩm: W5100_Shield
Nhà sản xuất: China
SL Giá
1 185,000đ
10 180,000đ
50 175,000đ
100 170,000đ
Qty
185,000đ
arduino-uno-r3
Arduino UNO R3
Arduino Uno Rev.3 (ATmega328P MCU)
View more
Mã Sản phẩm: Arduino UNO R3
Nhà sản xuất: China
SL Giá
1 215,000đ
10 210,000đ
50 205,000đ
100 200,000đ
Qty
215,000đ
arduino-due-r3
Arduino Due R3
Arduino Due Rev3 (Atmel SAM3X8E ARM Cortex-M3)
View more
Mã Sản phẩm: Arduino Due R3
Nhà sản xuất: China
SL Giá
1 455,000đ
10 450,000đ
50 445,000đ
100 440,000đ
Qty
455,000đ
arduino-leonardo-r3b
Arduino Leonardo R3B
Arduino Leonardo Rev3B ( ATmega32u4 MCU)
View more
Mã Sản phẩm: Arduino Leonardo R3B
Nhà sản xuất:
SL Giá
1 215,000đ
10 210,000đ
50 205,000đ
100 200,000đ
Qty
215,000đ