Easy Board GSM/GPRS/GNSS MC60 Module

ATC-E01

1 views
View detail

1. Introduction ATC-E01 Easy 

ATC-E01 Easy is a product designed by AT-COM to provide users with integrated facilities that are interconnected into a network through ATCBus.

The board is powered by the Quectel MC60-E01 module, which features GSM, GPRS, GNSS, Bluetooth 3.0. All are integrated in one module. The module also includes an OpenMCU feature for users to develop.

The MC60 is the latest 2G series, which delivers optimum performance in SMS, data and voice communications even in harsh environments. The ATC-E01-MC60 is full of features to provide you with ideas for wireless-based applications.

2. Product Specifications

  • Module MC60 Quectel:

+ GSM/ GPRS: Supports 850/900/1800/1900 MHz band.

+ Bluetooth: Standard 3.0, allowing data transmission up to 24Mbps

+ GNSS: GPS (up to 33 satellites supported)/ Glonass (up to 24 satellites supported).

+ Open CPU: Allows programming of applications directly on the MC60 without external microcontroller.

  • Module ATCE-01

Bluetooth Antenna: The IPX antenna and antenna on the board.

+ GSM Antenna: IPX Antenna Pad and SMA-RAF15.

+ GNSS Antenna: IPX Antenna Pad and SMA-RAF15.

+ Simcard and SD-Card: Integrated on one connector

+ Audio: Jack Audio 3.5

+ Source: MAX 5VDC power supply.

+ Push button: use MC60 ON / OFF.

+ 2 LEDs: power status indication (led power), and GSM/ GPRS signal status (led netlight).

Picture 1:  ATC-E01 viewed from the top

Figure 2: ATCE-02 viewed from the BOT.

Picture 2:  ATCE-02 viewed from the BOT

 3. Features of the ATC-E01 MC60 

      a. Module MC60-E01

 Module MC60

Picture 3: Module MC60

Module ATC-E01 mặt TOP

Picture 4:  ATC-E01 module TOP

ATC-E01 module on the BOT

Picture 5:  ATC-E01 module on BOT

Quectel integrates modern 2G technologies into its MC60-E01 with features such as GSM, GPRS, GNSS and Russian and US satellite systems, Bluetooth 3.0.

Cost saving for developers, Quectel has put OpenMCU technology into the module. Developers work on internal MCUs without using external processors.

     b. Supply

Power supply for ATC-E01-MC60 Easy via ATCBus at 5V and GND. It will then pass the source IC conversion to 4.0V supply to the MC60 module. This ensures a response up to 1.6Ampe and a drop in voltage when the load does not exceed 400mV.

4V Power Module for MC60

Picture 6:  4V Power Module for MC60

      c. Select the communication voltage

To accommodate the level of external devices when communicating with the ATC-E01 module, the board has a custom designed user interface with a 3.3V/ 5V logic voltage rating for application. When manufacturing, the voltage rating will be used at the 3.3V logic level.

Logic switch block communication

 

Picture 7:  Communication Logic Block

How to change the communication voltage:

  • Remove the 0R resistor (size 0805) in the unwanted position (face is at 3.3V).
  • Resist the 0R resistor (size 0805) to the desired position of 3.3V or 5V.

Picture location selection logic gates on ATCE-05.

Picture 8:  Logical position selection logic on ATCE-05

         d. Audio port and MIC

The product supports connectivity to the microphone via the 3.5mm jack to help users monitor and monitor the sound around the device.

 Audio Block

Picture 9:  Audio Block

        e. Antenna cho GSM/ GNSS

Bluetooth antennas, GPS, GSM / GPRS


Picture 10:  Bluetooth antennas, GPS, GSM/ GPRS antennas

With design of ATC-E01-MC60 integrated INPAQ antenna chip for Bluetooth and support 2 connect Antenna for GPS and GNSS. GNSS also has a circuit for Antenna Active. In addition, each antenna has an IPX layout for the user.

Position the antenna on the board

Picture 11:  Antenna position on the board

Antenna position on board (cont.)

Picture 12:  Antenna Location on Board

    f. LED display

Led NET and Power and PPS of GPS

Picture 13:  Led NET and Power and PPS of GPS

+ LED Power allows to display power status.

+ LED shows NET status of GSM network connection.

PPS LED shows the GPS signal status.

Position the leds on the board

Picture 14:  Position the leds on the board

    g. Push button

Multiplier module block MC60

Picture 15:  MC60 Multiplier Block Module

2 ways to power on/ off module MC60:

  • Option 1: Press the ON/ OFF button and keep it for about 2 seconds, designed on the circuit.
  • Method 2: Provide a high-level pulse to the PWR pin of the ATCBus Socket, the MC60 module will be powered on. When PWR pins are clicked, a few seconds later, the NetLight LED will blink and the MC60 module starts scanning the network, checking the SIMCARD ...

Button position on the board

Picture 16:  Button position on the board

4. Size

Mechanical size ATC-E01

Picture 17:  Mechanical Size ATC-E01

Price list

Quantity Unit Price Extended Price
1+ 0
Đang cập nhật.
Please enter correct your email
Content is your comment!
Content is too short to!
Comment is too long!
You can not continually write comments!

Related products